Computer-aided architectural design optimization based on BIM Technology
DOI:
https://doi.org/10.31449/inf.v46i3.3935Abstract
This article addresses the problem of the non-circulation of information in each stage of architectural design. This paper explores the architectural design process based on the BIM platform and puts forward the structural design method based on the BIM platform. It carries out the seismic analysis of a high-rise building with a transfer floor structure and compares the analysis results with the structural analysis software commonly used by the current design institute. The results obtained for experimentation show that the period ratio, displacement ratio, and the first six modes calculated by the two methods in the modal analysis are consistent. The error between calculation results and PKPM calculation results is within a reasonable range. In the analysis of the mode decomposition response spectrum method, the seismic forces in X and Y directions, floor shear, overturning moment, floor average displacement, and displacement angle obtained by the two models are compared respectively. The analysis results of the two methods accord with the mechanical characteristics of the transfer floor structure, and the calculation error is within the allowable range. The structural design based on the BIM platform has the advantages of high visualization, parameter-driven component size, and high model accuracy, improving design drawing efficiency.References
Schlueter, A., & Geyer, P. (2018). Linking BIM and Design of Experiments to balance architectural and technical design factors for energy performance. Automation in Construction, 86, 33-43.
https://doi.org/10.1016/j.autcon.2017.10.021
Veloso, P., Celani, G., & Scheeren, R. (2018). From the generation of layouts to the production of construction documents: An application in the customization of apartment plans. Automation in Construction, 96, 224-235.
https://doi.org/10.1016/j.autcon.2018.09.013
Ohki, C., Okamoto, T., Ohga, H., & Yoshizawa, N. (2018). Energy performance evaluation of outside sun shadings using radiance and newhasp. Journal of Environmental Engineering (Japan), 83(753), 861-870. https://doi.org/10.3130/aije.83.861
Ansah, M. K., Chen, X., Yang, H., Lu, L., & Lam, P. T. (2019). A review and outlook for integrated BIM application in green building assessment. Sustainable Cities and Society, 48, 101576.
https://doi.org/10.1016/j.scs.2019.101576
Ren, X., Li, C., Ma, X., Chen, F., Wang, H., Sharma, A., ... & Masud, M. (2021). Design of multi-information fusion based intelligent electrical fire detection system for green buildings. Sustainability, 13(6), 3405.
https://doi.org/10.3390/su13063405
Yuan, Z., Sun, C., & Wang, Y. (2018). Design for Manufacture and Assembly-oriented parametric design of prefabricated buildings. Automation in Construction, 88, 13-22.
https://doi.org/10.1016/j.autcon.2017.12.021
Kamel, E., & Memari, A. M. (2019). Review of BIM's application in energy simulation: Tools, issues, and solutions. Automation in construction, 97, 164-180.
https://doi.org/10.1016/j.autcon.2018.11.008
El Sayary, S., & Omar, O. (2021). Designing a BIM energy-consumption template to calculate and achieve a net-zero-energy house. Solar Energy, 216, 315-320. https://doi.org/10.1016/j.solener.2021.01.003
Du, J., Zou, Z., Shi, Y., & Zhao, D. (2018). Zero latency: Real-time synchronization of BIM data in virtual reality for collaborative decision-making. Automation in Construction, 85, 51-64.
https://doi.org/10.1016/j.autcon.2017.10.009
Al Hattab, M., & Hamzeh, F. (2018). Simulating the dynamics of social agents and information flows in BIM-based design. Automation in Construction, 92, 1-22.
https://doi.org/10.1016/j.autcon.2018.03.024
Ning, G., Kan, H., Zhifeng, Q., Weihua, G., & Geert, D. (2018). e-BIM: a BIM-centric design and analysis software for Building Integrated Photovoltaics. Automation in Construction, 87, 127-137.
https://doi.org/10.1016/j.autcon.2017.10.020
Heaton, J., Parlikad, A. K., & Schooling, J. (2019). Design and development of BIM models to support operations and maintenance. Computers in industry, 111, 172-186.
https://doi.org/10.1016/j.compind.2019.08.001
Lin, Y. C., Chen, Y. P., Yien, H. W., Huang, C. Y., & Su, Y. C. (2018). Integrated BIM, game engine and VR technologies for healthcare design: A case study in cancer hospital. Advanced Engineering Informatics, 36, 130-145.
https://doi.org/10.1016/j.aei.2018.03.005
Mattern, H., & König, M. (2018). BIM-based modeling and management of design options at early planning phases. Advanced Engineering Informatics, 38, 316-329.
https://doi.org/10.1016/j.aei.2018.08.007
Mesároš, P., Mandičák, T., & Behúnová, A. (2020). Use of BIM technology and impact on productivity in construction project management. Wireless networks, 1-8.
https://doi.org/10.1007/s11276-020-02302-6
Chen, R., & Sharma, A. (2021). Construction of complex environmental art design system based on 3D virtual simulation technology. International Journal of System Assurance Engineering and Management, 1-8.
https://doi.org/10.1007/s13198-021-01104-z
Jia, M., Komeily, A., Wang, Y., & Srinivasan, R. S. (2019). Adopting Internet of Things for the development of smart buildings: A review of enabling technologies and applications. Automation in Construction, 101, 111-126.
https://doi.org/10.1016/j.autcon.2019.01.023
Sun, H., Fan, M., & Sharma, A. (2021). Design and implementation of construction prediction and management platform based on building information modelling and three‐dimensional simulation technology in industry 4.0. IET collaborative intelligent manufacturing, 3(3), 224-232.
https://doi.org/10.1049/ cim2.12019
Wang, P., Sulaimani, H. J., & Kim, S. H. (2021). Digital model creation and image meticulous processing based on variational partial differential equation. Applied Mathematics and Nonlinear Sciences.
https://doi.org/10.2478/amns.2021.1.00047
Sun, Y., & Sharma, A. (2022). Research and Design of High Efficiency Superfine Crusher using CAD Technology. Computer-Aided Design and Applications, 19(S2), 26-38.
https://doi.org/10.14733/cadaps.2022.S2.26-38
Gong, P., & Li, J. (2022). Application of Computer 3D Modeling Technology in Modern Garden Ecological Landscape Simulation Design. Security and Communication Networks, 2022.
https://doi.org/10.1155/2022/7646452
Singh, P. K., & Sharma, A. (2022). An intelligent WSN-UAV-based IoT framework for precision agriculture application. Computers and Electrical Engineering, 100, 107912.
https://doi.org/10.1016/j.compeleceng.2022.107912
Zeng, H., Dhiman, G., Sharma, A., Sharma, A., & Tselykh, A. (2021). An IoT and Blockchain‐based approach for the smart water management system in agriculture. Expert Systems, e12892.
https://doi.org/10.1111/exsy.12892
Sharma, A., & Singh, P. K. (2021). UAV‐based framework for effective data analysis of forest fire detection using 5G networks: An effective approach towards smart cities solutions. International Journal of Communication Systems, e4826.
https://doi.org/10.1002/dac.4826
Sharma, A., Singh, P. K., & Kumar, Y. (2020). An integrated fire detection system using IoT and image processing technique for smart cities. Sustainable Cities and Society, 61, 102332.
https://doi.org/10.1016/j.scs.2020.102332
Hossain, M. A., Abbott, E. L., Chua, D. K., Nguyen, T. Q., & Goh, Y. M. (2018). Design-for-safety knowledge library for BIM-integrated safety risk reviews. Automation in Construction, 94, 290-302.
https://doi.org/10.1016/j.autcon.2018.07.010
Simeone, D., Cursi, S., & Acierno, M. (2019). BIM semantic-enrichment for built heritage representation. Automation in Construction, 97, 122-137.
https://doi.org/10.1016/j.autcon.2018.11.004
Cavalliere, C., Habert, G., Dell'Osso, G. R., & Hollberg, A. (2019). Continuous BIM-based assessment of embodied environmental impacts throughout the design process. Journal of Cleaner Production, 211, 941-952.
https://doi.org/10.1016/j.jclepro.2018.11.247
Röck, M., Hollberg, A., Habert, G., & Passer, A. (2018). LCA and BIM: Integrated assessment and visualization of building elements’ embodied impacts for design guidance in early stages. Procedia CIRP, 69, 218-223.
https://doi.org/10.1016/j.procir.2017.11.087
Hilal, M., Maqsood, T., & Abdekhodaee, A. (2018). A scientometric analysis of BIM studies in facilities management. International Journal of Building Pathology and Adaptation.
https://doi.org/10.1108/IJBPA-04-2018-0035
Schlueter, A., & Geyer, P. (2018). Linking BIM and Design of Experiments to balance architectural and technical design factors for energy performance. Automation in Construction, 86, 33-43.
https://doi.org/10.1016/j.autcon.2017.10.021
Yuan, Z., Sun, C., & Wang, Y. (2018). Design for Manufacture and Assembly-oriented parametric design of prefabricated buildings. Automation in Construction, 88, 13-22.
https://doi.org/10.1016/j.autcon.2017.12.021
Veloso, P., Celani, G., & Scheeren, R. (2018). From the generation of layouts to the production of construction documents: An application in the customization of apartment plans. Automation in Construction, 96, 224-235.
https://doi.org/10.1016/j.autcon.2018.09.013
Madan, J., Mani, M., Lee, J. H., & Lyons, K. W. (2015). Energy performance evaluation and improvement of unit-manufacturing processes: injection molding case study. Journal of Cleaner Production, 105, 157-170.
https://doi.org/10.1016/j.jclepro.2014.09.060
Soust-Verdaguer, B., Llatas, C., & García-Martínez, A. (2017). Critical review of bim-based LCA method to buildings. Energy and Buildings, 136, 110-120.
https://doi.org/10.1016/j.enbuild.2016.12.009
Ahsan, S., Guo, Z., Miao, Z., Sotiriou, I., Koutsoupidou, M., Kallos, E., & Kosmas, P. (2018). Design and experimental validation of a multiple-frequency microwave tomography system employing the DBIM-TwIST algorithm. Sensors, 18(10), 3491.
https://doi.org/10.3390/s18103491
Downloads
Published
How to Cite
Issue
Section
License
I assign to Informatica, An International Journal of Computing and Informatics ("Journal") the copyright in the manuscript identified above and any additional material (figures, tables, illustrations, software or other information intended for publication) submitted as part of or as a supplement to the manuscript ("Paper") in all forms and media throughout the world, in all languages, for the full term of copyright, effective when and if the article is accepted for publication. This transfer includes the right to reproduce and/or to distribute the Paper to other journals or digital libraries in electronic and online forms and systems.
I understand that I retain the rights to use the pre-prints, off-prints, accepted manuscript and published journal Paper for personal use, scholarly purposes and internal institutional use.
In certain cases, I can ask for retaining the publishing rights of the Paper. The Journal can permit or deny the request for publishing rights, to which I fully agree.
I declare that the submitted Paper is original, has been written by the stated authors and has not been published elsewhere nor is currently being considered for publication by any other journal and will not be submitted for such review while under review by this Journal. The Paper contains no material that violates proprietary rights of any other person or entity. I have obtained written permission from copyright owners for any excerpts from copyrighted works that are included and have credited the sources in my article. I have informed the co-author(s) of the terms of this publishing agreement.
Copyright © Slovenian Society Informatika
